PICkit 2 programmer is a compact, low-cost tool for programming and debugging Microchip PIC microcontrollers. Features a USB-B connection, status LEDs, and broad device support, with optional accessories for added flexibility.
Features:
Compact design for easy integration into any workspace.
USB-B connector for stable and reliable PC connection.
RM8U is an 8-channel USB-controlled relay module. It can be used to control electrical devices remotely from a PC over a USB port such as lamps, motors, and locks. RM8U features a wide operating voltage range (9-40V) and supports serial communication baud rate speeds starting from 2400 up to 115200 bps. RM8U module is well protected, filtered, and fully isolated.
The RM8N is an 8-channel wireless relay module based on the nRF24L01+ chip from Nordic Semiconductor. The nRF24L01 module is designed to operate in the global 2.4GHz ISM frequency band and uses GFSK modulation to transmit data. The card is well-protected, filtered, and easy to install. RM8N outputs can drive loads up to 10A (resistive loads).
Features:
Based on nRF24L01+ module.
On-board 3.3V,5V regulator.
Power input is filtered for noise reduction.
LED for power indication.
Operating voltage DC12V.
Eight output relays with red LED indicators.
Both normal open and normal close terminals are available.
Relay outputs are available through 5mm 2-pin K128 screw clamp terminals.
Easy configuration and test.
Reset push button switch is included.
DIN Rail mountable.
Four (Ø 3.5mm) mounting holes for easy installation.
RM4U is a 4-channel USB-controlled relay module. It can be used to control electrical devices remotely from a PC over a USB port such as lamps, motors, and locks. RM4U features a wide operating voltage range (9-40V) and supports serial communication baud rate speeds starting from 2400 up to 115200 bps. RM4U module is well protected, filtered, and fully isolated.
The RM6W is a 6-channel Wi-Fi module based on the ESP-12F module which is based on the ESP8266 chip from Espressif. The ESP-12F includes 4MB of flash and supports 802.11b/g/n Wi-Fi SOC. The ESP-12F can be programmed serially via the 4-pin header. The card is well-protected, filtered, and easy to install. The RM6W outputs can drive loads up to 10A (resistive load).
Features:
Based on ESP-12F Wi-Fi module.
On-board 3.3V regulator AMS1117-3.3V.
Power input is filtered for noise reduction.
Green LED for power indication.
Operating voltage DC12V.
Six output relays with red LED indicators.
Both normal open and normal close terminals are available.
Output terminals are available through a 5mm 2-pin K128 screw clamp.
Easy firmware uploading using a 4-pin header ( 3.3V, Tx, Rx, GND ).
Reset push button switch is included.
Two yellow LEDs for Tx and Rx signal indication.
DIN Rail mountable.
Four (Ø 3.5mm) mounting holes for easy installation.
SNM-H module is a smart serial USB (H-type connector) to wireless module based on the nRF24L01+ from Nordic Semiconductor and uses the controller ATMEGA8.
The nRF24L01+ module is designed to operate in the global 2.4GHz ISM frequency band and uses GFSK modulation to transmit data.
ATMEGA8 microcontroller comes pre-programmed to support RMxN relay modules protocol. However, the user can program ATMEGA8 microcontroller with other firmware.
SNM-H module uses a CH340 chip as a USB to Serial converter.
Features:
Compatible with the protocol of RMxN wireless relay module.
SNM-B module is a smart serial USB (B-type connector) to wireless module based on the nRF24L01+ from Nordic Semiconductor and uses the controller ATMEGA8.
The nRF24L01+ module is designed to operate in the global 2.4GHz ISM frequency band and uses GFSK modulation to transmit data.
ATMEGA8 microcontroller comes pre-programmed to support RMxN relay modules protocol. However, the user can program ATMEGA8 microcontroller with other firmware.
SNM-B module uses a CH340 chip as a USB to Serial converter.
Features:
Compatible with the protocol of RMxN wireless relay module.
SNM-A module is a smart serial USB (A-type connector) to wireless module based on the nRF24L01+ from Nordic Semiconductor and uses the controller ATMEGA8.
The nRF24L01+ module is designed to operate in the global 2.4GHz ISM frequency band and uses GFSK modulation to transmit data.
ATMEGA8 microcontroller comes pre-programmed to support RMxN relay modules protocol. However, the user can program ATMEGA8 microcontroller with other firmware.
SNM-A module uses a CH340 chip as a USB to Serial converter.
Features:
Compatible with the protocol of RMxN wireless relay module.
