ESP-01 Programmer Adapter
70.00 EGPIn stock
ESP-01 programmer adapter, USB (CH340) to ESP8266 WiFi development board module.
USB to UART TTL Module (CH340) Header to Header
70.00 EGPIn stock
Low-cost USB to serial UART/TTL converter module based on CH340 chip.
Features :
- USB (Header) to serial TTL (header).
- Supports 3.3V/5V.
- Provides RX, TX, DTR, and RTS signals.
- Suitable for breadboard applications.
- Dimension: 23 X 20 X 12mm.
1-Channel Wireless Relay Module ESP-01 RM1W
65.00 EGPIn stock
1-Channel wireless relay module ( ESP-01 Wi-Fi ).
Features :
- Wireless: Wi-Fi (2X4 2.54mm female header for ESP-01S Module).
- Operating Voltage: DC5V.
- Output Rating: One relay output (Normally open and normally closed) 10A MAX (resistive load) Port pin IO0.
- Red LED for Relay status.
- Green LED for power indication.
- RST switch for reset operation.
- One (Ø 3.5mm) mounting hole for easy installation.
- Dimensions: 35 X 32 X 17mm.
2-Channel DC Power Distributor
60.00 EGPIn stock
This module is a generic 2-channel DC power fuse distributor board.
Features :
- Operating voltage: 5~48 DCV.
- Maximum output current: 10A/channel.
- Protection fuse for each channel.
- Green LED indicator for input voltage.
- Red LED indicator for each output voltage.
- 100nF filter capacitor for each output channel.
- Four (Ø 3.5mm) mounting holes for easy installation.
- DIN Rail mounting using PCB carrier or PCB bracket ( Optional ).
- Dimension: 72 X 58 X 15mm.
2-Channel Active High Relay Module(24V) RM224
60.00 EGPIn stock
2-Channel relay module (24V) up to 10A rated current directly interfaced to a microcontroller or TTL logic.
USB to UART TTL Module (CH340) USB Socket Type A Male to Header
60.00 EGPIn stock
Low-cost USB to serial UART/TTL converter module based on CH340 chip.
Features :
- USB type A male connector.
- Supports 3.3V/5V.
- Provides RX, TX, DTR, and RTS signals.
- Suitable for breadboard applications.
- Dimension: 52 X 18 X 12mm.
Out of stock
Load Cell Module (HX711)
60.00 EGPOut of stock
This module provides an easy way to interface microcontroller to any load cell. It is based on HX711 IC which provides a high-resolution analog-to-digital converter and uses a two-wire interface (clock and data) for communication. A very accurate weight measurement can be obtained with some calibration.
Features :
- Operating Voltage 2.7V- 5.5V.
- Operating Current: 1.5mA.
- Resolution 24 bit.
- Output data rate 10SPS or 80SPS.
- Operation temperature range: -40 ~ +85℃.
- Dimension : 38 X 30 X 3mm.
Bluetooth Adaptor
60.00 EGPIn stock
Bluetooth adapter module is a hardware tool suitable for configuring Bluetooth modules via PC using a HyperTerminal or any other configuration software.
2-Channel Active High Relay Module (12V) RM212
60.00 EGPIn stock
2-Channel relay module (12V) up to 10A rated current directly interfaced to microcontroller or TTL logic.
2-Channel Active High Relay Module (5V) RM205
60.00 EGPIn stock
2-Channel relay module (5V ) up to 10A rated current directly interfaced to microcontroller or TTL logic.
L298 to Pin Header
60.00 EGPIn stock
Dual H-Bridge L298 IC driver to pin header breakout board, Suitable for DC Motor Driving or interfacing to L297 to easily build stepper motor driver.
ESP-01 Adapter Module
55.00 EGPIn stock
ESP-01 adapter module for serial communication to microcontroller and Arduino board.
ESP-01 not included.
I²C Serial EEPROM Module 24CXX
Price range: 25.00 EGP through 50.00 EGPIn stock
I²C Serial EEPROM Module 24CXX.
Features:
- Operating voltage: 5V.
- Green LED for power indication.
- Interface: 2.54mm male pin header.
- One (Ø 3.5mm) mounting hole for easy installation.
- Breadboard-friendly module.
- Dimension: 22 X 10 X 8mm.
On Delay Timer Module (1-10 Sec)
50.00 EGPIn stock
Switch on delay timer module based on NE555 timer IC.
Features :
- Based on NE555 timer IC.
- Operating voltage: 5V, 12V Jumper set.
- Delay time range: 0-10 Sec Pot adjustable.
- Output: Relay dry contact (Normally open, Common, Normally close).
- Maximum output power: 2200W.
- Maximum output current: 10 ampere.
- Reverse polarity protection.
- Green LED for power indication.
- Red LED for output indication.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimension: 74 x 26 x 17mm.
DB9 Vertical Female to Screw Terminal + Pin Header
50.00 EGPIn stock
DB9 female socket vertical type on PCB to block terminals and pin header facilitates solderless connection to standard serial connector DB9 and is also suitable for panel mounting and test applications.
Features :
- DB9 pins are routed to pin headers and screw clamp terminals.
- Both terminals are labeled according to the DB9 pin number to which they are routed.
- Pin header pitch distance 2.54mm.
- Screw terminal pitch distance 3.5mm.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 50 X 30 X 25mm.
Out of stock
DB9 Vertical Male to Screw Terminal + Pin Header
50.00 EGPOut of stock
DB9 male socket vertical type on PCB to block terminals and pin header facilitates solderless connection to standard serial connector DB9 and is also suitable for panel mounting and test applications.
Features :
- DB9 pins are routed to pin headers and screw clamp terminals.
- Both terminals are labeled according to the DB9 pin number to which they are routed.
- Pin header pitch distance 2.54mm.
- Screw terminal pitch distance 3.5mm.
- Four (Ø 3.5mm) mounting holes for easy installation.
- Dimensions: 50 X 30 X 25mm.